1.1Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed, refer to ASTM F2200 for additional gate types. When an obstruction is sensed during gate opening the gate will reverse for 4 seconds then stop. Class II - Commercial/General Access Vehicular. Model CSL24UL • • • • • CSL24ULTECH For a gate operator utilizing a contact sensor such as an edge sensor: One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as at the leading edge, trailing edge and post mounted both inside and outside of a vehicular horizontal slide gate. † This model is for use on vehicular ... LiftMaster 300 Windsor Drive Oakbrook, IL 60523 PHOTOREGISTER SM CSL24UTECH. •ALL power wiring should be on a dedicated circuit and well protected. Exception: All other fixed stationary objects greater than 16 in. The location of the power disconnect should be visible and clearly labeled. NOTE: If the operator is not grounded properly the range of the remote controls will be reduced and the operator will be more susceptible to lightning and surge damage. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length. For pedestrian access in the vicinity of an automated vehicular gate, a separate pedestrian gate shall be provided. 2.Run the AC power wires to the operator. 2.Run wire from the earth ground rod to the operator. fire, police) may be placed at any location in the, The Stop and/or Reset (if provided separately) must be located in the. Weld the bottom bracket in this position. All exposed pinch points are eliminated or guarded, and guarding is supplied for exposed rollers. 1. The operator should be on a separate fused line of adequate capacity. Illustrations provided by DASMA Gate Systems Safety Guide. •Test ALL entrapment protection devices after completing installation of the operator. Weld the upper bracket in this position. Chain should not be too tight or have excessive slack. •The entrance is for vehicles ONLY. 6.The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and closing to reduce the risk of entrapment. Expansion board - up to 3 entrapment protection devices configurable to either close or open and up to 4 edge sensors using wireless edge sensor kit model LMWEKITU . NOTE: If using an external receiver use shielded wire for the connections and mount the receiver away from the operator to avoid interference from the operator. 3.2The following provisions shall apply to Class IV vehicular horizontal slide gates: 3.2.1All weight bearing exposed rollers 8 feet (2.44 m), or less, above grade shall be guarded or covered. THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. 1.6A gate latch shall not be installed on an automatically operated gate. Replace the outlet housing by securing with the screws. Send it in by texting the photo to 71403. •Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts, walls, pillars, columns, or operator itself. An alternative to a concrete pad is to post mount the operator (refer to Accessories). NEVER let children operate or play with gate controls. Take a photo of the camera icon including the points ( ). LiftMaster monitored external entrapment protection devices MUST be used with LiftMaster operators to meet UL325 requirements, see. After adjusting the force or the limit of travel, retest the gate operator. 6.Connect the black wire to HOT using a wire nut. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE. Gates shall have smooth bottom edges, with vertical bottom edged protrusions not exceeding 0.50 inches (12.7 mm) when other than the exceptions listed in ASTM F2200. We have emailed you a verification link to, BG770 Industrial-Duty Single Arm Barrier Gate Operator, CSL24V High-Cycle Commercial Slide Gate Operator with Battery Backup, CSW24V High-Cycle Commercial DC Swing Gate Operator, EL2000 Telephone Entry for Commercial Applications and Gated Communities, GH Heavy Industrial-Duty Gear-Reduced Hoist Operator, GH5HP 5 HP Heavy Industrial-Duty Gear-Reduced Hoist Operator, KPR2000 Single Entry Access Control Keypad and Proximity Reader, LA400 Residential DC Linear Gate Operator, LA412 Solar Powered Residential Gate Operator, LA500 Residential / Light Commercial Swing Gate Operator, of the camera icon including the points (, Every installation is unique. The pedestrian access opening shall be designed to promote pedestrian usage. The earth ground rod can be grounded to the chassis. Weld the front bracket in this position. ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment. Install the earth ground rod within 3 feet (.9 m) of the operator. 3.Align the top bracket so the chain will be level with the top idler pulley and parallel to the ground. The gate operator is only one component. A wireless device such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. Weld the bottom bracket in this position. The ground wire must be a single, whole piece of wire. •Entrapment protection device types include inherent (built into the operator), monitored external photoelectric sensors or monitored external edge sensors, •This operator is provided with an inherent entrapment protection device built into the operator that serves as one of the two independent devices. An optional Transformer Kit (Model 3PHCONV) can be used to change the input voltage (208/240/480/575 Vac) to an output voltage of 120 Vac (refer to Accessories). It is the responsibility of the installer to ensure that ALL entrapment zones are protected with an external monitored entrapment protection device, protecting both the open and close gate cycles. Protrusions shall not be permitted on any gate, refer to ASTM F2200 for Exceptions. When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of Serious Injury or Death if you do not comply with the warnings that accompany them. b.Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving. CSL24UL 24VDC High-Traffic Commercial Slide Gate Operator Ideal for high-traffic, heavy-duty application. These stops shall be installed at either the top of the gate, or at the bottom of the gate where such stops shall horizontally or vertically project no more than is required to perform their intended function. COMMERCIAL DC VEHICULAR SLIDE GATE OPERATOR Model CSL24U The gate operator should be installed near the front roller of the gate. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. b.A hard wired contact sensor shall be located and its wiring arranged so the communication between the sensor and the gate operator is not subject to mechanical damage. Each gate system is specifically designed for an individual application. For a copy, contact ASTM directly at 610-832-9585 or www.astm.org. Each placard is to be visible by persons located on the side of the gate on which the placard is installed. This specification shall not apply to gates generally used for pedestrian access and to vehicular gates not to be automated. This input will be disregarded during gate opening. NOTE: The earth ground rod can be grounded to the chassis. •Use the emergency release ONLY when the gate is not moving. 1. An existing gate latch shall be disabled when a manually operated gate is retrofitted with a powered gate operator.
Bms Medical Abbreviation Blood,
Technical Architect Roles And Responsibilities In Software,
Enderman Spawner Farm,
Popular Mexican Candy,
Buddha Twitch Stats,
Neighboring Sermon Series,
Samsung Galaxy Book Flex Alpha Review,